RemoteTx Manual
remotetx.net

Troubleshooting

Work through the section that matches what you see. Most problems are a single setting.

The radio does not key#

The KEY lamp lights on the CW tab, but the radio stays in receive.

  1. Use radio key input (Mute MIC) must be ticked. Without it the tone isn't sent to the station.
  2. The correct sound card must be selected and active. On the Audio tab, the USB-CW-VOX adapter must be chosen as the Sound Card, and Start/Restart Audio clicked (see Levels). To check: turn the radio's AF gain up and down. If the receive audio you hear changes with it, the VOX adapter's sound card is selected, which is correct. If it doesn't, the Pi is still using the radio's built-in sound card.
  3. The CW button on the Radio tab must be lit and connected to the USB paddle adapter, RemoteTx PTT-CW. If it isn't lit, click it and choose the adapter. See Turning on the CW button.
  4. TX level on the CW tab should be set to 100 %, and TX Mod on the Audio tab set as described in Levels.
  5. Rise/fall to radio should be unticked. Shaped edges can make the VOX detector switch late or not at all on short dits.
  6. The radio must be in CW mode, key type straight, with break-in (semi or full) on.
  7. Check the cable from the adapter's key out to the radio's KEY jack, and that the adapter is plugged into the Pi.

The KEY lamp doesn't light#

  • Audio off: click Start audio. Browsers need a click on the page before they may make sound.
  • Keyboard: click inside the CW tab first so it has focus.
  • Paddle: see The paddle isn't detected.

The paddle isn't detected#

  • Check the adapter's PC / Phone switch. Use PC with Chrome or Edge on a computer. On a phone or tablet, or in Safari or Firefox, use Phone, and tap inside the CW tab so it has keyboard focus. See PC / Phone switch.
  • In PC mode, use Chrome or Edge.
  • On the Radio tab, click CW and answer Yes, choose device, then pick RemoteTx PTT-CW. If it isn't in the list, unplug and replug the adapter and try again. See Turning on the CW button for screenshots of each step.
  • If the adapter was granted before but isn't reconnecting, click Connect HID paddle on the CW tab to open the chooser again.
  • The status next to HID paddle → keyer tells you whether it's connected and which device it's using.

Pressing the paddle puts the radio in TX instead of sending CW#

The adapter is in PTT mode. Click CW on the Radio tab (or Connect HID paddle on the CW tab). In CW mode the client stops using the adapter's contacts for PTT. See Turning on the CW button for screenshots of each step.

Dits and dahs are swapped#

Tick Reverse paddles on the CW tab.

Too many (or too few) extra elements in Iambic B#

Adjust Squeeze latch. Lower values give more of Iambic B's extra elements; higher values give fewer. If you never want the extra element, use Iambic A.

My signal sounds heavy, light or choppy#

  • Heavy or light: the station's tone detector may react a little differently at key-down and key-up. Adjust Weight a few percent.
  • Choppy, dropped dits at high speed: raise TX level, and make sure Rise/fall to radio is off. Check your Internet connection; heavy packet loss can drop audio.
  • Listen on an SDR or a second receiver to judge the result; your local sidetone is always perfect and won't show station-side problems.

I hear an echo of my own sending#

The radio's CW monitor (or your own signal in its receiver) comes back after the round-trip delay. Either:

  • tick Mute radio audio while sending and adjust hold, or
  • turn the radio's CW monitor off.

The receive decoder prints garbage#

  • Raise Squelch until noise stops printing.
  • Narrow the radio's CW filter.
  • Untick Auto tone and set RX Tone to the signal's pitch if another signal is close by.
  • Make sure Pause while sending is on so your own signal isn't decoded.

iPhone / iPad: the sidetone goes quiet when the radio audio plays#

Tick Radio audio through keyer (iPhone). It's on by default on iOS.

© RemoteTx® · remotetx.net · Manual built 2026 · Updated 2026-11-19