Icom 7100 Quick Start

The Icom 7100 has a USB port that allows both CI-V radio control as well as sound control.  It also supports turning the radio on and off while power is continuously supplied to the radio. The radio can also be remote controlled without the control head being attached if #11 below is set to OFF.

Icom 7100 Preparation:

Several settings are required for the IC-7100 to work properly with RemoteTx.

  1. SET -> Connectors -> USB Audio SQL: ON
  2. SET -> Connectors -> ACC/USB Output Select: AF
  3. SET -> Connectors -> ACC/USB AF Level: 50%
  4. SET -> Connectors -> USB MOD Level: 50%
  5. SET -> Connectors -> DATA OFF MOD: USB
  6. SET -> Connectors -> CI-V -> CI-V Baud Rate: Auto
  7. SET – Connectors -> CI-V -> CI-V Address: 88h
  8. SET -> Connectors -> CI-V -> CI-V Transceive: ON
  9. SET -> Connectors -> CI-V -> CI-V Output (for ANT): OFF
  10. SET -> Function -> Time-Out Timer (CI-V): 3min
    In case all control is lost due to a USB malfunction, radio will stop transmitting after 3 minutes.
    See FCC Part 97.213
    If network connection is lost while transmitting, RemoteTx will automatically switch the radio back to Rx within a minute regardless of the above setting assuming there has not been a USB/CI-V control malfunction between the RPi and the radio.
  11. SET -> Function -> Power OFF (With No Contoller): OFF
    This allows the radio to be powered on and off remotely without the control head being connected.

Setup procedure:

  1. Connect the usb port on the IC-7100 to any of the usb ports on the RPi with a USB cable.
  2. Plug the ethernet network port on the RPi into an Internet connected router with a cat5 network cable. (Wifi can be configured later once initial connection is established via ethernet.) Remember to copy the ‘remotetx.conf’ file to the ‘/’ folder of the RPi SDCard first.
  3.  Apply power to the RPi so that it boots up.  It should take about 1 to 2 minutes. During this time it will acquire a network address from the router and automatically connect via the Internet to the RemoteTx service.
  4. Make sure power is applied to the radio. (The radio does not have to be on. RemoteTx can turn it on and off.)

Remote Control:

  1. Using a Mac, PC, tablet or phone open a browser (Chrome or Safari) to https://your-callsign.remotetx.net
  2. At the login prompt, enter your RemoteTx username and password.
  3. Accept the prompt to allow the use of the microphone by the browser.
    It is important that your device you has a working microphone or the audio will not start and you may not get the microphone prompt from the browser.
  4. You may also be prompted to save your password.  This is a good idea if you are using a device that you use often.
  5. The RemoteTx station control interface will appear showing the ‘Settings’ tab.
  6. Select IC-7100 from the radio choices. The default radio settings should not need to be changed for a basic setup.
    The settings should be:  USB Port:USB-0 and Baud Rate: 19200 and CI-V Addr: 88
  7. Select the upper  ‘Radio’ tab and click on the ‘Connect IC 7100 ‘ button. This will initiate a control connection to the radio and show it’s current status. (It could be on or off.)
  8. If the radio status is ‘OFF’ click the ‘On ‘ button to bring the radio online and display its controls. (This can take a few seconds for the radio to start.)
  9. The radio control interface should now be online.
  10. Select the upper ‘Audio ‘ tab and in the ‘Remote Audio’ area select the ‘USB Audio Codec’ sound card choice.
  11. Click on ‘Start/Restart Audio 1’.
  12. Wait about 5 seconds after which the ‘Call Radio’ and ‘Hang Up ‘ buttons should appear in the ‘Local Audio’ area.
  13. Click on the ‘Call Radio’ button to initiate bi-directional audio to the radio. If audio becomes disrupted due to unreliable network conditions, clicking ‘Reset Local’ will re-initiate the browser audio and re-clicking the ‘Set Audio 1’ button will re-initiate the RasPi audio. (Normally re-clicking the ‘Set Audio 1’ button is only necessary if there has been an Internet disruption at the radio site.)
  14. Return to the upper ‘Radio’ tab to operate the radio.

Typical Radio Control Settings:

RemoteTx allows setting the most frequently used controls during typical operation. Buttons either toggle features on and off or cycle through available values. Slider controls allow setting variable values. Following are initial settings that are known to work well. They can be fine tuned to personal preference as experience is gained with the solution.

  • Mod-Source: USB  (This sets the Data Off Mod source to USB which is required for Tx.)
  • USB-TX: 50
  • COMP: ON  (Button will be blue color, this is important)
  • COMP LEVEL: 5
  • RF-GAIN: 100 or as preferred
  • USB-RX: 50
  • AF-GAIN: Has no effect so leave at 0. If it is above 0, the radio speaker will be heard at the station location.

The rest of the controls are self explanatory to an operator experienced with the Icom 7100.
If you are using a Mac or PC with a mouse that has a roller button, the roller can be used to change the values of controls that the mouse is hovering over. This includes the individual frequency digits and slider controls.

Disconnecting from Radio:

Release control of the radio in this order.

  1. Select upper ‘Radio’ tab.
  2. Click the ‘OFF’ button to turn the radio off if this is desired (it can also be left on, ready for the next connection).
  3. Click the ‘Disconnect IC 7100’ to release remote control of the radio.
  4. Close the browser to disconnect from the RPi.